• wrapper.group property
• wrapper.*.group property
• wrapper.group.strict property

Kompatibel :	3.5.38
Editionen :
Betriebssysteme :

This property makes it possible to automatically change the group of certain files that the Wrapper creates, producing the same result as the 'chown' command used in a terminal on a UNIX system. The group specified will be used as the default value for all the properties listed below.

A valid value is the name or the ID of an existing group on the system where the Wrapper is used. The Wrapper should however either run with the root user or a user that belongs to the target group, or else a permission denied error will be reported when attempting to change the group.

The default value is '-UNCHANGED-' which means the Wrapper will not change the group, and the responsability of its assignment will be left to the OS. Usually the primary group of the user who own the Wrapper process is used, or the group of the parent directory if the Setgid bit is set on the parent directory. Note that hyphens ('-') have voluntarily been included in the default value to avoid any conflict as they make it an illegal group name.

wrapper.group=jenkins

Kompatibel :	3.5.38
Editionen :
Betriebssysteme :

It is also possible to specify the group for particular files created by the Wrapper by using the following properties. Each defaults to the value of the wrapper.group property.

• wrapper.anchorfile.group :

  Specifies the group to assign when creating the anchor file. See the wrapper.anchorfile property.

• wrapper.lockfile.group :

  Specifies the group to assign when creating the lock file. See the wrapper.lockfile property.

• wrapper.pidfile.group :

  Specifies the group to assign when creating the pid file. See the wrapper.pidfile property.

• wrapper.statusfile.group :

  Specifies the group to assign when creating the status file. See the wrapper.statusfile property.

• wrapper.java.idfile.group :

  Specifies the group to assign when creating the Java id file. See the wrapper.java.idfile property.

• wrapper.java.pidfile.group :

  Specifies the group to assign when creating the Java pid file. See the wrapper.java.pidfile property.

• wrapper.java.statusfile.group :

  Specifies the group to assign when creating the Java status file. See the wrapper.java.statusfile property.

• wrapper.logfile.group :

  Specifies the group to assign when creating the log file. See the wrapper.logfile property.

Kompatibel :	3.5.38
Editionen :
Betriebssysteme :

When the Wrapper starts, several checks are performed to ensure that the wrapper.*.group properties are set with an existing group name or id, and that the Wrapper either runs as the root user or as a user that belongs to the configured groups. Although this is required for the value to be valid, this doesn't completely guaranty that the group can successfully be assigned at runtime. There are a number of reasons why the Wrapper may fail to assign a group to a file during execution. It is indeed possible that the group list or the belonging of users to a group change while the Wrapper is running.

If wrapper.group.strict is set to TRUE, the Wrapper will stop with a FATAL error whenever an invalid group is detected while loading the configuration. This property will however not cause the Wrapper to stop if it later fails to assign the group while running. Instead an error will be reported and the group will be simply unchanged.

If wrapper.group.strict is set to FALSE, any invalid group will be resolved to the value of wrapper.group, or failing that, to '-UNCHANGED-'.

The default value is FALSE.

wrapper.group.strict=TRUE

• wrapper.log.lf_delay.threshold (3.5.10)

  Legt einen Schwellenwert fest, ab dem JVM-Nachrichten aufgeteilt werden, die sonst zu lang wären, um auf einmal ausgegeben werden zu können.

• wrapper.log.warning.threshold (3.5.8)

  Ausgabe einer Warnung, wenn ein Logeintrag mehr als die spezifizierten Anzahl an Sekunden braucht, um ausgegeben zu werden.

• wrapper.logfile (1.0.0)

  Legt den Pfad zur Wrapper-Logdatei fest.

• wrapper.logfile.close.timeout (3.5.21)

  Regelt die Anzahl an Sekunden nach den die Log-Datei nach dem letzten Logeintrag geschlossen werden soll.

• wrapper.logfile.flush.timeout (3.5.21)

  Konfiguriert das Zeitintervall in Sekunden, nach dem der Wrapper alle Ausgaben in die Logdatei ausgibt.

• wrapper.logfile.format (2.2.5)

  Konfiguriert das Format der Ausgaben, die an die Logdatei gesendet wurden.

• wrapper.logfile.inactivity.timeout (3.2.0)

  Regelt die Anzahl an Sekunden nach den die Log-Datei nach dem letzten Logeintrag geschlossen werden soll.

• wrapper.logfile.loglevel (2.2.5)

  Filtert an die Logdatei gesendete Nachrichten entsprechend ihrer Protokollierungsstufen.

• wrapper.logfile.maxfiles (2.2.5)

  Regelt die maximale Anzahl an "gerollten Dateien".

• wrapper.logfile.maxsize (2.2.5)

  Regelt die maximale Größe der "gerollten Dateien".

• wrapper.logfile.purge.pattern (3.3.8)

  Regelt das Dateimuster, um alte Logdateien zu löschen.

• wrapper.logfile.purge.sort (3.3.8)

  Konfiguriert den Sortiermodus der "gerollten Dateien", um die letzten zu löschen.

• wrapper.logfile.rollmode (3.2.0)

  Legt den Rollmodus der Logdatei fest.

• wrapper.logfile.group (3.5.38)

  Spezifiziert die beim Erstellen der Logdatei zuzuweisende Gruppe.

• wrapper.logfile.umask (3.2.0)

  Spezifiziert die beim Erstellen der Logdatei zu nutzende umask.